PULS

Power supply unit

FIEPOS series

FPS300 Basic 1AC series

Field AC/DC Power supply unit (PSU) / converter

IO-Link interface

85Vac-264Vac (100Vac / 110Vac / 120Vac / 200Vac / 208Vac / 220Vac / 230Vac / 240Vac nom.; 47-63Hz)
264-300Vac input overvoltage (for 500ms max.)
80Vac turn-ON voltage
70Vac shutdown voltage

88Vdc-360Vdc (100Vdc / 110Vdc / 120Vdc / 127Vdc / 200Vdc / 220Vdc / 250Vdc nom.)

LED bar-graph (20-200% load)
"Status" LED

Single-phase (1AC) or DC

12.5A (at 24Vdc)

360W (-25...+45°C)
300W (-25...+55°C)
150W at +70°C (derates linearly between +55°C and +70°C)
600W short-term (for 5s; at -25...+55°C)
300W short-term (for 5s; at +55...+70°C)

24Vdc-28Vdc (adjustable)
200mV turn-ON overshoot

37ms (buffer time at 120/230Vac input)

HanQ4/2 female connector (INPUT; X1)
5-pin M12 connector (IO-Link interface; X2)
HanQ4/0 male connector (OUTPUT; X3)

output overvoltage protection (31.8Vdc typ. / 32.5Vdc max.)
Overload / short-circuit current -- 25A / 0A at heavy overloads (when output voltage falls below 13V) the power supply delivers continuous output current for 2s. Then the output is switched OFF for approx. 18s before a new start attempt is automatically performed. This cycle is repeated as long as the overload exists. If the overload has been cleared the device will operate normally. Load impedance 10mΩ. Discharge current of output capacitors is not included.
Over-temperature protection -- Output shutdown with automatic restart. Temperature sensors are installed on critical components inside the unit and turn the unit OFF in safety critical situations which can happen e.g. when ambient temperature is too high ventilation is obstructed or the derating requirements are not followed. There is no correlation between the operating temperature and turn-OFF temperature since this is dependent on input voltage load and installation methods.
Series / parallel operation -- not possible
Back-feeding loads max. 35V / 4J -- The unit is resistant and does not show malfunctioning when a load feeds back voltage to the power supply. It does not matter whether the power supply is ON or OFF. The absorbing energy can be calculated according to the built-in large sized output capacitor.

0.956 (230Vac input)
0.942 (120Vac input)

IO-Link

Hanging and fixing via integrated keyholes or by screw mounting

1s start-up delay (100-230Vac input)
22ms rise time (nominal input; constant full current load; 0mF load capacitance)
35-48ms rise time (nominal input; constant full current load; 12.5mF load capacitance)

IP65
IP67

W182mm x H183mm x D59mm

Aluminium housing

-25...+55 °C
(with linear derating) +55...+70 °C

1.68A (230Vac input; full output)
3.2A (120Vac input; full output)
3.98A (100Vac input; full output)
2.9A (110Vdc input; 24Vdc / full output)
1.04A (300Vdc input; 24Vdc / full output)
6A peak inrush (at 230Vac input)
2.6A peak inrush (at 120Vac input)

(230Vac input; full output load) 16.2 W
(120Vac input; full output load) 22.4 W

(230Vac input) 0.97
(120Vac input) 0.99

Commercialized

FPS300241002101

(output stage) 12500 μF

CE marking
cULus Listed
IECEE CB Scheme IEC 62368-1 / IEC 61010-2-201
IEC 61010
IEC 60950-1
SEMI F47
VDMA 24364
ROHS
REACH
WEEE
IEC/EN 61558-2-16

IP65/67 protection
600W peak 5s
100-240V wide-range input
95.6% full load and excellent partial load efficiencies
DIN rail mounting possible (option "D")
Output connected to PE (PELV)
Version without connection to PE on request
Large output capacitors
Not potted
Negligible low input inrush current surge
Full power between -25°C and +55°C
DC-OK
3 years warranty
The FIEPOS Basic series offers 1 DC output and is available with a power of 300W or 500W.
The IP54; IP65 and IP67 field power supplies are perfect for the decentralized supply of 1-phase or 3-phase systems and machines.
The field power supplies can be easily connected in parallel; e.g.
to increase total performance or realize a reliable redundant system.

50mVpp (20Hz...20MHz; 50Ω)